View non-flash version
New & Notable between Valencia and the Balearic Islands - Majorca and Ibiza. Rodriquez Cantieri Navali SpA, builder of advanced aluminum vessels including fast ferries, patrol boats, and luxury yachts, constructed TMV 115 at its Pietra Ligure yard located outside of Savona, Italy. The sea-trials were concluded suc- cessfully and a testament to the high degree of engineering and expertise that went into the construction of this all- aluminum vessel. Specifically, the ves- sel achieved a better than expected ser- vice speed of 38.3 knots with the four Caterpillar 3816's at 90 percent MCR, with 400 tons of deadweight, and with the ride control system installed and active. The ride control system was designed and manufactured by Rodriquez Marine Systems, a subsidiary of Rodriquez Cantieri Navali SpA, and consists of four anti-roll fins with forward and aft T-foils all centrally controlled by an advanced bridge mounted system. Inte- grated into the aft T-foil skegs are trim tabs that are used to steer the vessel at speeds over 15 knots thereby allowing the waterjets to remain in their optimal thrust position. Circle 5 on Reader Service Card www. maritimereporterinfo. com Main Particulars - Aquastrada TMV 115 Length, (o.a.) 377 ft. (115 m) Length, (waterline) 316 ft. (96.2 m) Beam 56 ft. (17 m) Draft 17 ft. (5 m) DWT 700 Engines 4 x 7,200 kW Diesels Waterjets x steerable Lips Ride Control System .. .Rodriquez Marine Systems Passengers 900 Elliott Bay Develops Eco-Tourism Vessel s • =:.' • Elliott Bay Design Group (EBDG) has created a design for a new 230 ft. (70.1 m), 127-passenger Eco-tourism vessel for Nisa Navegacion of Santiago, Chile. Known as Mare Australis, the vessel will join the existing 210-ft. (64-m), 90- passenger Terra Australis in providing one-week excursions from Punta Arenas to the Straits of Magellan, Tierra del Fuego, and Cape Horn. Elliott Bay's designers worked to ensure that three important requirements were met during the vessel's construc- tion; beginning with the idea that the design had to be as close a possible to that of Nisa's existing vessel, while complying with current SOLAS require- ments. The second point was to provide the utmost in seakeeping characteristics while maintaining an easy-to-build hull form. Thirdly, because the new boat will be constructed in Chile, the design has to incorporate both metric-size plate thicknesses, as well as English-measure structural shapes and piping. The all-stateroom vessel will feature two lounges and will provide daily shore excursions for passengers via onboard RIBs. The company's contract design is currently undergoing review for classing by ABS, and construction is expected to commence during the third quarter 2001, with delivery occurring in the fourth quarter 2002. The steel vessel will have a beam of Innovative Shipyard Tools Reduce Staging And Fit-Up Time! Circle 212 on Reader Service Card www.maritimereporterinfo.com CAPAC® CORROSION PROTECTION GOES A LONG WAY SHAFT-GROUND ASSEMBLY SHAFT-HULL MILLI-VOLTMETER ANODE POWER SUPPLY/CONTROLLER MONITOR REFERENCE ELECTRODE DIELECTRIC COATING CAPASTIC — ANODE POWER SUPPLY/CONTROLLER REFERENCE ELECTRODE CAPAC corrosion protection systems are designed for higher quality and longer life than competing systems. At a lower installed cost. Retrofit your ocean-going vessel or offshore platform with CAPAC systems today, and realize the full benefits of long-term protection tomorrow. Contact USFilter's Electrocatalytic Products at 2 Milltown Court, Union, NJ 07083 Phone: 908-851-2277, Fax: 908-851-6906. www.usfilter.com .VIVENDI water company EC-CA-0041-AD-201 The Pul-Ton is a tool that converts the pushing force of a jack into a pulling force for joining large hull sections. Up to 25 ton capacity per jack. The Bulb-Align a tool for aligning Holland Bulb Profile Stiffners when joining panel sections. Ship Fit Tools is a remarkable new line of Specialty Tools designed specifically to aid the Ship Fitter with material handling and fit-up. Ship Fit Tools are designed to facilitate the work of a plate fitter in ship building and steel fabrication. If staging and fit up work are a bottleneck in your yard, then there maybe a Ship Fit Tool to help you. Ship Fit Tools Distributed by: Weld Tooling Corporation 3001 West Carson Street Pittsburgh, PA USA15204-1899 Phone: 1-412-331-1776 1-800-245-3186 Fax: 1-412-331-0383 http://www.bugo.com ok ce The Bulb-Mov-R is a gripper for handling Holland Bulb Profile Stiffners. 1.5, 3 and 5 ton models. The Pul-Jak is a ratcheting jack for pushing or pulling bulkheads, frames and hull sections. 7, 12 and 20 ton models are available. Circle 289 on Reader Service Card www. maritimereporterinfo. com
