View non-flash version
(Continued from page 90) Ferro Corporation CopperCladR Bottom Coating Sys- tem is a permanently-attached anti- fouling hull coating that can be sprayed in-mold by the manufac- turer of fiberglass boats or post- applied by an authorized applicator to existing fiberglass boats. Report- edly, CopperClad coatings are envi- ronmentally acceptable alternatives to ablative bottom paints — cost- effective coatings that do not leach or "fall off' and provide a safe, long- lasting finish. CopperClad is regis- tered with the EPA. For more infor- mation on Ferro Corporation, Circle 192 on Reader Service Card Hempel Paints Ltd. Ballast spaces are a problem Hempadur LTC 4514 and 4515 were designed to solve. These products are reportedly suited to the total protection of such areas due to their chemical structures. The products reportedly afford: no restriction in use through coal tar or isocyanate content; light colors to ease inspec- tion during application and subse- quent surveys; and better tempera- ture resistance. "Hard" coatings with abrasion- resistant properties, they also em- brace tolerant recoating intervals and reportedly are equally suitable for segregated and combined cargo/ ballast spaces. The high volume solids (82-85 percent, depending on shade) pro- vide not only low VOC emissions, but increased area coverage. The low-temperature curing Hempadur LTC 4514 provides an application temperature down to minus 15 de- grees F. For more information on Hempel Coatings, Circle 95 on Reader Service Card Sigma Coatings With today's demands for higher safety, economic benefits and more stringent environmental concerns, Sigma Coatings is already well-es- tablished in R&D programs directed toward the future. Products range from the high- grade, tin-free self-polishing anti- fouling Sigmaplane Ecol to solvent- free tank coating systems such as the combined spray and fill epoxy Sigmaguard CSF and the ballast tank coating Sigmaguard BT. Sigma Alumastic is a high-solid, VOC-compliant self-priming surface tolerant epoxy coating. Specially developed for rusted areas where only surface preparation by power tool or hydroblasting is possible, it provides resistance to abrasion, im- pact, water and mild chemicals, and can reportedly be overcoated with epoxy, polyurethane, alkyd, acrylic and chlorinated rubber paints. For more information on Sigma Coatings, Circle 116 on Reader Service Card Stan-Blast Abrasives Stan-Blast has added new items to their product line that will help customers comply with the stricter regulations imposed by the Depart- ment of Environmental Quality (DEQ) and the EPA. The new items are: Blastox, containment screens and other low free silica abrasives, such as garnet and glass beads. Blastox is blended with abrasives before blasting to render spent abra- sives non-hazardous and acceptable for disposal in standard landfills. Containment systems are meant to meet most stringent environmental regulations by containing and cap- turing overspray and spent abra- sives . Stan-Blast abrasives are listed on the Navy's Qualified Products List. For more information on Stan- Blast products, Circle 199 on Reader Service Card The T.D.J. Group T.D.J, is an environmental ser- vices company that markets dry chemistry for use in a variety of markets to render heavy metal waste non-hazardous under TLCP test- ing. Blastox™ is a blasting additive used with traditional abrasives and equipment to render spend abra- sive waste non-hazardous for lead and other metals under TLCP test- ing without RCRA permitting. Blastox blended abrasives are re- portedly being used on Navy vessels and in ship yards to reduce the cost of handling abrasive waste. Re- gional capabilities for beneficial re- use of spent abrasives (versus land- fills) are being set up regionally, which reduces potential liability for the generator. For more informa- tion on the T.D.J. Group, Circle 104 on Reader Service Card Leave Traditional Shot & Grit Behin MET grain" Steel Abrasive Gives You the Power of Shot with the Cleaning Efficiency of Grit. METgrain® is the new steel abrasive that's generations ahead of conventional abrasives for cleaning steel surfaces of paint and scale in an environmentally sound manner. Industry leaders are switching to METgrain® for improved performance and lower cost. For new construction or repair METgrain® is the optimum blast cleaning abrasive. • Efficiently removes paint, rust or scale. • Lower paint consumption. • Less coating failures. • Lower cost & no scrap surcharge. • Cleaner work environment. • 99% reduction in generated waste. • Compatible with air or rotary blast cleaning equipment. CHESAPEAKE SPECIALTY PRODUCTS 410/388-5055 Fax 410/388-5194 5055 North Point Boulevard Baltimore, Maryland 21219 Owned and Operated in the U.S.A. Circle 317 on Reader Service Card Unitor Unitor's Corroless Rustkil range comprises two rust-stabil ing primers for conventiona reachable ship areas, and two cor sion-inhibiting aerosol sprays : other areas. The surface-tolerg Anti-Rust primers can reportec be painted on after removing loc rust for long-term corrosion proti tion. Anti-Rust Spray 1 reportec protects nuts, bolt heads, flangi crevices, window frames and pc holes, hinges, valves and stored coi ponents. Anti-Rust Spray 2 is ; electrical spray that dries to a cle£ thin film and can reportedly be us< to protect the internals of electric junction boxes, switchgear, navig tion lights, communications equi ment, electrical motors and tools storage. For more information ( Unitor, Circle 193 on Reader Service Card U.S. Paint AWLGRIP High Solids Urethar Coating Systems reportedly me< rigorous performance standards ei tablished during five years of la and field research, and are current] being globally test marketed in fres and salt water. AWLGRIP Hig Solids were developed in respons to concerns of lowering solvent emif sions while offering the exception* performance advantages of the cor ventional urethane AWLGRIP proc uct line. Reportedly low in VOCf AWLGRIP High Solids reportedl have high impact and chip resis tance, high gloss retention, excel lent flow control and flexibility c application. Manufactured in quart and gallons, a wide range of stocl and custom colors have been formu lated. For more information oi AWLGRIP High Solids Uretham Coatings Systems from U.S. Paint Circle 194 on Reader Service Card U.T. Technologies HYCOTE Epoxy Coatings anc adhesives, from U.T. Technologies reportedly perform under adverse environmental conditions — pro- viding all the expected benefits oi epoxy-based systems. Application can usually be made using one ol the seven Product Application Mod- ules (PAMs) which help guarantee a properly mixed and prepared prod- uct. U.S. government agencies have reportedly been applying HYCOTE 151 to ship hulls without removing them from the water. Oil compa- nies in the U.S., Mexico and Brazil have used HYCOTE 151 for applica- tions along the waterline of offshore platforms and inland on pipelines where condensation prevents the use of traditional coatings systems. For more information on HYCOTE from U.T. Technologies, Circle 198 on Reader Service Card 90 Maritime Reporter/Engineering News
