View non-flash version
? FMC Seeks Comments On Exempting Military Rates From '84 Ship Act The Federal Maritime Commis- sion (FMC) has issued an Advance Notice of Proposed Rulemaking (ANPRM) to solicit comments from the public regarding whether mili- tary rates should be exempted or made fully subject to the filing re- quirements of section 8, and possi- bly section 10, of the 1984 Shipping Act. If the FMC's treatment of mili- tary rates is seen as making mean- ingful comparisons difficult or un- fair to MSC, U.S.-flag carriers or any other party, the commission could remove format exemptions presently enjoyed by U.S.-flag op- erators filing military rates and re- quire such rates to be published in exactly the same manner and for- mat as commercial rates, e.g., tariffs and service contracts. However, if military rates do not present such difficulties, a full or partial exemption from the 1984 Shipping Act requirements may be warranted. The exemption could be limited to the tariff filing require- ments of section 8, 46 U.S.C. app. 1707, or extended to the provisions of section 10 as well. Comments are due 45 days after the June 3, 1992 publication of the ANPRM in the Federal Register. For further information contact: Robert D. Bourgoin, General Counsel, Federal Maritime Commis- sion, 1100 L St., N.W. Washington, D.C. 20573. (202) 523-5740. French Yard Unveils High-Speed Vessel For Passengers/Cars The Design and Engineering De- partment of French shipbuilder Ate- liers et Chantiers du Havre (ACH) recently unveiled a long, highly streamlined single-hull project ves- sel with small lateral wings designed for passenger transport with or with- out vehicles. The yard, which is currently build- ing the Club Med 2 for Club Med, said the proposed range of vessels will be capable of carrying between 50 and 2,200 passengers and 20 to 550 cars, with a waterline length ranging from 25 to 150 meters (82- 492 feet). At fully loaded cruising speeds, ACH claims the vessel will be able to obtain speeds of 50 knots, a sharp contrast with current car- ferry speeds of 20 to 22 knots. The research and test campaign were partially backed by the French Ministry of Industry. For further information on ACH, Circle 59 on Reader Service Card Meyer Werft Cancels Plan To Build New Yard In Former East Germany Amid pressure from its fellow German and European competitors, shipbuilder Meyer Werft of Papenburg recently announced it had canceled plans to build a modern shipyard on an island in the former East Germany. Meyer Werft had been pursuing a plan to build a yard in the industrial district of the har- bor of Mukran on the island of Rugen since early 1990. The cancellation follows a recent preliminary decision by the EC to reduce shipyard capacity in Mecklenburg-Vorpommern. Meyer Werft has been active in the revitalization of several former East German yards, including Rostock, Stralsund, Rechlin and Wolgast. For example, through its active and successful support to Volkswerft, Stralsund, especially in the way of new orders, Meyer Werft has been able to secure em- ployment at the yard. Fuel Injection Problems? Centerline Power has the Answers. We specialize in fast economical repair and replacement parts for Diesel Fuel Injection systems. We're centrally located for quick turn- around... plus, three decades of experience means we do it right. MAN/B&W SULZER MIRRLEESI BLACKSTONE DIAHATSU YANMAR AKASAKA WARTSILA/SWD FUEL PUMPS INJECTORS NOZZLES PLUNGER-BARREL DELIVERY VALVES RELIEF VALVES B&W INJECTOR SPECIALISTS "Marine Diesel Fuel Injection Specialists" We manufacture Sulzer Fuel Nozzles Centerline Power 1375 Sherman Drive, Longmont, CO 80501 Ph: 303-440-6441 FAX: 303-772-3473 Circle 209 on Reader Service Card ANCHORS CHAINS 1/2" up to 4V2", U2/U3 from STOCK! C. J. Wortelboer jr. B.V. Eemhavenstraat 2-6 P.O. Box 5003 3008 AA Rotterdam Holland Telephone: (0)10-4292222 Telex: 28393 CJWNL WORTELBOER HEAVY DUTY HAND WINCHES Automatic Brake Holds Load & Prevents Recoil r Heavy Duty Worm • Designed for continuous heavy duty applications • Rigid all steel frame construction • Six models: 550 to 11,000 lbs line pull Compact Lightweight • Light but tough for heavy duty applications • All cast aluminium construction • Four models: 150 to 1100 lbs line pull Heavy Duty Sealed Gear • All gears totally enclosed and permanently lubricated • Silent in operation • Ideal for corrosive or contaminated areas • Three models: 550 to 1650 lbs Controlled Free Fall • Load can be lowered by controlled free fall • Automatic brake governs pay out speed to predeter- mined maximum • Load stops instantly and is held on release of handle • Four models 660 lbs to 3300 lbs line pull JEAMAR WINCHES INC. 1051 Clinton St., Buffalo, N.Y. 14206 TEL (716) 854-3211 FAX (416) 889-3795 Circle 268 on Reader Service Card Circle 230 on Reader Service Card 29 July, 1992
