View non-flash version
Belgian Shipbuilder "Floats7 Massive GRP Mold On Film Of Air the way by two to six workers. Approximately one pound of force will move 1,000 pounds on the air bearings. An average mold section requires 20 to 30 pounds of total pushing force by the workers to move it. The six female mold parts on the other side of the hull (against a wall) are kept in permanent posi- tion by hold-down bolts. To remove the GRP hull itself, the 14 air bearings are again placed under the keel beams supporting the hull, and the beams are connect- ed by cable to four side winches. Transport of the 200-ton hull across the floor on air bearings to the next work station 50 feet away is fast, easy, and safe, according to plant manager E. De Winter. "The entire move is made at the rate of about 14 feet per minute with the side winches pulling, and six men helping guide and at the central control station," says Mr. De Winter. "When the hull mold arrives at the second work station, it is quickly and accurately aligned again, as GRP is a very flexible material." Re-erection of the mold parts starts immediately by sliding the air bearings under the six mold parts, inflating the bearings, and pushing the mold parts into place so they are precisely positioned to form the next GRP hull. The air bearings are deflated in seconds, removed, and the mold is prepared for producing the next hull. "The air bearings keep the shop floor free from any obstructions and make it easy to clean," says Mr. De Winter. "In addition to our use of the air bearing system to move heavy and cumbersome mold parts, which require gentle movement and accurate positioning, we use the air bearings to quickly move many oth- er parts and equipment in the plant. The system is working out quite satisfactorily in our molding opera- tion." When the ships are completed, they will constitute part of a Tripar- tite Agreement between Belgium, France, and the Netherlands to build up to 40 GRP minesweepers. These vessels are intended to reju- venate the mine countermeasure naval capability of each member country. For additional information and free literature on the Aero-Go air bearings, Circle 96 on Reader Service Card The 50-foot move of a 160-foot- long, 200-ton glass fiber reinforced polyester (GRP) mold is done safely in 3Vi minutes on a film of air at the Mercantile-Beliard N.V. shipbuild- ing plant in Ostend, Belgium. Each of six mold sections are moved the same way by the yard, which is in the middle of completing a govern- ment contract to build 10 new GRP minesweepers — one every six months. Using the air bearing sys- tem, savings in labor time and equipment costs are considerable, according to G. Delhasse, techni- cal assistant manager at the new plant. As minesweepers must be non- magnetic, GRP hulls were specified, requiring production of a special workshop to meet stringent Belgian military specifications. When the contract was signed, however, a plant for molding large hulls in GRP did not exist in Belgium, so Mercan- tile-Beliard began almost immedi- ately to build one. One year later the 10,000-square-foot facility was com- pleted, fully air conditioned, and equipped with extensive dust con- trols to accommodate polyester res- in molding production. Erection of gantry cranes was first considered to handle the heavy mold, but proved to be too costly because of their limited use. Floor rails were also considered and re- jected because of the desire for flexi- bility of movement and an unen- cumbered floor. Air bearings were finally selected for their limited load-bearing capacity, clean opera- Six workers easily push 14-ton mold section away from GRP hull using air bearings man- ufactured by Aero-Go. Inc. of Seattle, which permit omnidirectional travel. tion, omnidirectional travel, and low cost, according to company offi- cials. The ship's hull mold is made of 17 parts—four bottom parts, 12 side parts, and a transom flat panel. All are connected by bolted flange and centering pins. When the hull mold- ing is completed and stiff enough to be moved without permanent dis- tortion, the four bottom parts are removed and replaced by seven spe- cially built keel beams. These beams are used with air bearings to raise the ship's hull a few inches out of the mold. This is done by inserting a modular load-handling system of 14 air bearings, designed and manufac- tured by Aero-Go., Inc. of Seattle, under each end of the seven keel beams and then applying shop air. In seconds, the air bearings in- flate, raising the keel beams and the ship's hull approximately 2 inches out of the mold form. Next, the keel beams are chocked to free the air bearings, allowing the bearings to be removed and used in a similar way to move the six mold parts on one side of the hull. These mold parts are easily pushed across the floor on a film of air and positioned out of Navigation Sciences Offers VIEWNAV® Master Mariner Brochure A full-color "VIEWNAV® Master Mariner Electronic Chart Naviga- tion System" brochure is available from Navigation Sciences, Inc. of Bethesda, Md. The four-page bro- chure describes and illustrates the VIEWNAV system used by opera- tors of pilotboats, ferries, tugboats, and others who want to navigate more accurately in difficult harbor conditions. Using proprietary software, the VIEWNAV system interfaces with onboard radar to provide a bright, true-motion radar display of sur- rounding activity, super-imposed on full-color, NOS-quality digitized Electronic Charts. Radar land clut- ter—one of the problems with stan- dard radar displays, which can make target detection difficult—is com- pletely masked out on the Electron- ic Charts. This makes radar inter- pretation easier and faster by more clearly defining radar images of ves- sel traffic, and other targets. Buoys, navaids, and channels are shown in actual chart colors in selected scales from one to 48 NM square. Precise positioning is accom- plished using differential Loran-C, accurate to five yards, and by ad- vanced "radar map matching." The system can interface with onboard radar, gyrocompass, speed log and most Latitude/Longitude inputs, such as Loran, SatNav, Decca, Ome- ga and GPS. The VIEWNAV sys- tem can also be interfaced with closed cirucit TV systems such as those found on cruise ships to allow crew and passengers to monitor the progress of the ship. The VIEWNAV Master Mariner Electronic Chart Navigation System consists of a 14, or 20-inch Full- Color Display Monitor, a Control Console, Main Equipment Cabinet, and any number of remote moni- tors. For free literature containing full information, Circle 31 on Reader Service Card Bailey Offers New Color Brochure On Recorders And Data Loggers A new color brochure featuring the latest process recorders and data loggers is now available from Bailey Controls of Wickliffe, Ohio. Highlights of Bailey's line of modu- larly designed recorders include de- scriptions, functions, special fea- tures and options, and advantages of each recorder model. Bailey recorders feature precali- brated, interchangeable, plug-in components for application versatil- ity. They provide precise tracking, and come with easily accessible dis- play charts or high-resolution win- dows. Bailey Controls is a division of Babcock & Wilcox, and a leading supplier of instrumentatin, controls, and computer systems for power generation, process automation, and energy management in the petro- chemical, electric utility, and pro- cess industries. B&W is a major operation unit of McDermott Incor- porated, a subsidiary of McDermott International, Inc. For a free copy of the High-Per- formance Recorders brochure, Circle 35 on Reader Service Card Individual 36-inch-square air bearings under post supporting weight of mold section. GRP hull chocked on seven keel beams with air bearings underneath, in process of being winched sideways across floor. System is made up of 14 Aero-Go air bearings. 36 Maritime Reporter/Engineering News
