View non-flash version
nected to the end of the airlift conveyor/classifier — all skid- mounted. CAB reports that Mr. Svobada anticipates a $75,000 savings by the use of the recoverable steel grit over other nonrecyclable sub- stances and a 50 percent increase in productivity due to lack of dust and improved visibility. The system also can be mount- ed on a 40-foot trailer and used dockside for blasting ships' tanks and hulls. CAB developed a weathertight blasting capsule for side-mounting on the hull of a drydocked vessel which permits recovery and recycling of steel abrasives. Either the skid or trailer arrangement can be used for work on the interiors and exteriors of large industrial tanks. For more information on the CAB system, Write 17 on Reader Service Card $15.2-Million Increase Awarded Westinghouse For Nuclear Components Westinghouse Electric Corpo- ration, Plant Apparatus Divi- sion, Wilkins Township, Pa., has been awarded a $15,209,000 face- value-increase to a previously awarded cost-plus-fixed fee con- tract for naval nuclear propul- sion components. The Naval Sea Systems Command, Washington, D.C., is the contracting activity (N00024-77-C-4002). Preform To Supply 26 Sets Of Fiberglass Barge Covers —Brochure Available Proform, Inc. of Minneapolis, Minn., manufacturer of struc- tural fiberglass inland and ocean barge covers, recently received an order for 26 sets of inland lift-off covers from American Commercial Barge Lines, Jeffer- sonville, Ind. Company literature describes the fiberglass covers that result in added cargo ton- nage, are one third the weight of steel covers, are noncorrosive, and easy to maintain. For more information, Write 25 on Reader Service Card M.A.N. To Build Three Floating Cranes With Voith-Schneider Propulsion The Saudi Ports Authority re- cently awarded M.A.N, in Nur- emburg, West Germany, as gen- eral contractor, an order for three floating cranes with a lift- ing capacity of 200-tons each. The pontoons are being con- structed by M.A.N.-GHH Dock and Shipbuilding Company. They measure: length 60 meters, breadth 21.7 meters, trial run draft 2.38 meters, with a dis- placement of about 2,150 tons. Like the two 200-ton floating cranes Dammam and Jeddah that March 1, 1983 are already in service, the new cranes are designed to operate without tug assistance. They will be equipped with Voith-Schneider propulsion systems. The cranes are to be used in the ports of Jeddah, Jubail, and Gizan. Depending on the amount of work to be performed, it is planned to transfer the cranes from port to port without tug assistance. In view of the rela- tively high free-running speed of about 8 knots, a three-propel- ler system was selected. The total input power of each crane is 1,640 kw, distributed over two size 21 G 11/135 pro- pellers, each of 600 kw, and a size 18 G 11/115 VS propeller of 440 kw. The propellers are driven elec- trically by three-phase a.c. squir- rel-cage motors. To utilize the installed power as ideally as pos- sible for maneuvering and for the compensation of wind forces, the two larger propellers are ar- ranged at the crane-mast end of the pontoon, i.e., near the center of the lateral windage area. These are located in recesses. The third propeller is installed freely in the raised pontoon bottom. The Band-It Clamping System Who would econo- mize with inferior clamps in an expen- sive operation like this? For offshore oil applications — and hundreds of other uses — Band-It clamps are available in 201 and 316 stainless steel and other materials. And The Band-It tool quickly and easily secures the assembly. Call (303) 320-4555 for the name of your nearest industrial Band-It distributor and ask for a free 24-page guide to clamping Band-It Band-It Division. HoudaiUe Industries, Inc. P.O Box 16307 Denver. Colorado 80216 303-320-4555 Telex 45-0009 Write 635 on Reader Service Card Co B MARINE SALES REPRESENTING gjfad (RllbbsLh &>• Rubber Sleeve or Flange Bearings Stuffing Boxes and Keel Coolers Heavy Duty Fendering WESTERN BRANCH METALS Armco Stainless Shafting Systems Machining — Propeller Nuts DAMAN INDUSTRIES Ceramaloy Coatings Propeller Shaft Liners Dredge Pump Sleeves and Shafts KAHLENBERG BROS. Air Horns — S/S Propellers NATIONAL FLUID SEPARATORS, INC. Bilgemaster Automatic Oily/Water Separator Systems SCHRADER BELLOWS Pneumatic Propulsion Control Systems P.O. Box 33, Glenhead, N.Y. 11545 516-676-3738 A.L.Don introduces the 'Next Step' in pilot ladders. A.L. Don proudly introduces its new, improved pilot ladder—with steps you can replace quickly and easily, right on board your own vessel. A specially designed mechanical clamp holds each step in place. So there's no need to unstring the ladder. No special tools required. The A.L. Don Pilot ladder carries a U.S. Coast Guard approval and meets or exceeds all SOLAS regulations and IMO standards with features like a newly designed, non-skid surface... Steps painted international safety orange... Synthetic polypro-dacron suspension ropes with a white outer jacket and orange inner safety core... and bottom steps molded from a synthetic that can easily withstand loads of over 700 pounds with less than %" of deflection. The new A.L. Don pilot ladder is pending a patent; available from coast-to-coast... and, best of all, we offer these innovations at prices far lower than those of our competitors. Your next step is to send for the free technical literature to help you select the pilot ladder that's right for your vessel. To receive this information, just circle the reader service number. Or write or call us today. Headquarters: A.L. DON COMPANY Division of Steelstran Industries, Incorporated Foot of Dock Street, Matawan, NJ 07747 (201) 541-7880 • Telex: 139374 A.L. DON, WEST Roberton & Schwartz Sales Co., Inc. 722 Folger Ave. Berkeley, California 94710 (415) 845-9336 -Telex: 176148 Write 385 on Reader Service Card Write 1491 on Reader Service Card 33
