View non-flash version
THE BOSTON METALS COMPANY THE BOSTON METALS COMPANY THE BOSTON METALS COMPANY THE BOSTON METALS COMPANY THE BOSTON METALS COMPANY FALK IN-LINE MARINE REVERSE REDUCTION GEAR SUITABLE TO 1600 HP WITH MODIFICATIONS 700 HP @ 750/246 RPM—30" clutch drum—ratio 3.05:1—equal to new. Can be used with up to 1600 HP by modifying with larger clutch drums & tires. 313 E. Baltimore St. Baltimore, Md. 21202 539-1900 (301) 355-5050 313 E. Baltimore St. Baltimore, Md. 21202 539-1900 (301) 355-5050 NEW UNUSED NAVY SURPLUS UNIVERSAL FAIRLEADS SHIPBOARD TYPE 4 Rollers — 8"xl8"—2 horizontal mount—2 vertical mount. Clear op- ening 3". Center to center on verti- cal & horiz. rollers 11". Fairlead 36" overall width—24" high—24" deep. 28 available. $695 Each 313 E. Baltimore St. Baltimore, Md. 21202 539-1900 (301) 355-5050 313 E. Baltimore St. Baltimore, Md. 21202 539-1900 (301) 355-5050 G.M. 3-268A 100 KWA.C. Diesel GENERATOR SET Like new, ENGINE: G.M. 3-268A —-3 cylinder—6'/2"x7" bore & stroke. GENERATOR: Century — 100 KW—440 volts—3-phase— 60 cycle. Switchgear available. AIR $9450 ELECTRIC $7775 STARTING A'tJU STARTING L # / J 313 E. Baltimore St. Baltimore, Md. 21202 539-1900 (301) 355-5050 ENGINE: GM 16-278A—Vee type 8%"xlOV2"—air start- ing—heat exchanger cooled and complete with filters, strainers, engine operating panel board and all accessories. GEAR: Folk—3.05:1 ratio—vertically offset in line. Will sell engines & gears separately UNUSED l5/s" HEAVY DUTY LINK BELT WINDLASS Below deck motor drive. Double wildcat—driven by 50 HP 230 VDC motor with vertical shaft and worm drive. Single speed—handles 7000 lb anchors and 60 fathoms of 1 s/b" chain at 7 fathoms per minute. Wildcat centers 56". Com- plete with all controls and warping features. Total weight 27,500 lbs. With spares. ATTENTION! TUG OWNERS GM 1700 HP Geared Diesel Sets 2 Sets Available MARINE PUMPS 115 Volts D.C. Very Little Use FIRE & BILGE 350 GPM—100 lb. head—1750/3500 RPM—40 H.P. Furnished with Nash Hytor Pump MO-571 & float switch, for self-priming. All controls. Pump & primer weight 900 lbs. BILGE & FLUSHING 15 GPM—20 lb. head—1750/3500 RPM—% HP motor. Furnished with Nash Hytor MD-2 vacuum pump. Approx. weight 250 lbs. SANITARY SERVICE 35 GPM—40 lb. head—3500 RPM—1 H.P. Pump weight 40 lbs. DIESEL FUEL OIL TRANSFER Positive displacement—gear head—15 GPM—20 lb. head —350 RPM—1 HP—pump weight 260 lbs. LUBE OIL SERVICE Positive displacement—gear head—30 GPM—35 lb. head —273 RPM—2 HP motor—weight of pump 350 lbs. THE BOSTON METALS COMPANY 313 E. Baltimore St. Baltimore, Md. 21202 539-1900 (301) 355-5050 2 LIDGERWOOD DOUBLE DRUM TOWING WINCHES CAPACITY: Each drum stows 1800' of 1 Vi" wire. Each drum independently 30,000 lbs. on 2nd layer at from 10 to 50 feet oer minute. Both drums simultaneously 15,000 lbs. each. Drums equipped with clutch shift levers. 24" Winch heads for 8" circumference manila rope. Static load 52,000 lbs. applied at mid-lenqth. Base 10' 6" wide with 2 outboard winch heads 20W' each. Drum diameter 221/2"—flange 50"—28" between flanges. Equipped with level wind spooling devices and compres- sor hand brake. MOTOR: 75 HP—under deck with hori- zontal drive throuqh worm gear. Drip-proof—fully pro- tected. Mfg by A'llis-Chalmers—type EB-127-DC—com- pound wound—125/250 volts—254 amps—reversible— 575/1150 RPM. CONTROLLER: Allis-Chalmers drum type —with 1 off position and 5 heave in positions and five payout conditions in opposite directions. Control cabinet also located below deck. Worm gear reduction 62T at I'/j CP worm wheel 31:1 reduction. Drum shaft beveled bull gear 61T. Drive shaft beveled pinion gear 14T— ratio 4.857:1. THE BOSTON METALS COMPANY 313 E. Baltimore St. Baltimore, Md. 21202 539-1900 (301) 355-5050 REVOLVING FIELDS WESTINGHOUSE For T2SE—A-l tankers—with A.B.S.—ex-Caltex J.H. Mac- Garegill. THE BOSTON METALS COMPANY 313 E. Baltimore St. Baltimore, Md. 21202 539-1900 (301) 355-5050 UNUSED ALLIS-CHALMERS FIRE & GENERAL SERVICE PUMPS 200 GPM — 180' head — 2 1/2,'x2"—bronze—flange connections. MOTOR: 20 HP—1 15 volts DC—2400 RPM—153 amps. THE BOSTON METALS COMPANY 313 E. Baltimore St. Baltimore Md. 21202 539-1900 (301) 355-5050 m G.M. 8-268A 200 KW A.C. DIESEL GENERATOR SETS ENGINE: 8-268A—6i/2" bore x 7" stroke—1200 RPM— driving 200 KW Westinghouse generator—440 volts—3- phase—60 cycle—321 amps—80% power factor at 1200 RPM. Switchgear available. $3750 THE BOSTON METALS COMPANY 313 E. Baltimore St. 539-1900 Baltimore, Md. 21202 (301) 355-5050 2-STAGE 5x4x4 50 CFM @ 150 LBS INGERSOLL RAND AIR COMPRESSOR Class R—type 30—5x4x4—750 RPM 3-cylinder air cooled 2-stage compressor with air intake filter. 20 HP Vee-belt drive motor—440 volts—3-phase—60 cycle—27 amps— 1800 RPM continuous duty—class A insulation—ball bearing dripproof squirrel cage—low starting current. Motor weight 500 lbs. Complete with GE magnetic starter size 2—27.2 amps—weight 75 lbs. Copper finned inter- cooler between stages. Total weight motor, compressor and base 1505 lbs. OAL: 4' 15/8"; OAW: 2' 6'/2"; OAH 3' 21/2". THE BOSTON METALS COMPANY 313 E. Baltimore St. 539-1900 Baltimore, Md. 21202 (301) 355-5050 60 KW GM 6-71 DELCO DIESEL SET GM 6-71 engine with Delco 120 volt DC 500 amp gen- erator with stab, shunt. THE BOSTON METALS COMPANY 313 E. Baltimore St. 539-1900 (301) Baltimore, Md. 21202 355-5050 NEW - UNUSED ROTARY DISPLACEMENT DELAVAL IMO 8" DEEP WELL PUMPS for oil 840 GPM at 50 PSI DIS. PRESS. Pump RPM 1450. Equipped with right angle drive transmission suitable for any diesel or gas engine running at 1450 RPM. Right angle drive ratio 1:1. Suction lift flooded—50 HP required. Viscosity range SSU-130-500. These pumps are specially designed for submerged operation in oil. Pump case, inlet nozzle & thrust washer are bronze. Total hgt from center of drive shaft to base 9'9". Hgt from deck mounting plate to center of drive shaft 361/2". From deck mounting plate to bottom suction 6'8!4". Pump is self-lu- bricating. Suitable for oil barges & all deep well uses, Further details on request. SPECIALLY PRICED AT 53750 EACH THE BOSTON METALS COMPANY 313 E. Baltimore St. 539-1900 Baltimore, Md. 21202 (301) 355-5050 60 Maritime Reporter/Engineering News
